Habitest - Liquid Feeders
H14-03M : Liquid Delivery Reservoir – Mouse
H14-03R : Liquid Delivery Reservoir – Rat
Module Height: 1 Unit (delivery tip is stainless steel)
The delivery reservoir used inthis module is the same as used in the H14-04 below. It is fitted with needle tubing on the rear to receive a catheter sized tube from the source. It receives fluid from an infusion pump or other delivery pump. It is an alternative to the gravity-feed model below and is used for greater precision or when small volumes of costly fluid are used.
H14-04M : Liquid Solenoid Valve – Mouse
H14-04R : Liquid Solenoid Valve – Rat
Module Height: 4 Units
Lamp Type: 1819 (delivery tip is stainless steel)
The solenoid valve is designed to dispense non-viscous fluids. It should be used for water, drugs in water solution, but not heavy suspensions or solutions that leave a sticky residue such as sugar. The quantity delivered is controlled by means of a combination of the supply bottle height, valve adjustment and the duration of activation. The delivery cup reservoir will hold fluid until consumed by the animal. A 1 litre supply bottle with a compatible fitting is supplied with the unit.
H14-05M : Liquid Dipper – Mouse
H14-05R : Liquid Dipper – Rat
Module Height: 4 Units
Lamp Type: 85 (the rat module is totally stainless steel
This module is designed to deliver any type of liquid from water to highly viscousfluids as condensed milk. The dipper cup rests in the fluid. When a 28 VDC operate signal is applied to the damped solenoid, the cup is raised to an accessible position in the bottom of the magazine.
Rat opening - 32mm x 41mm
Mouse opening - 22mm x 22mm
The solenoid provides direct, fast operation with no electrical noise or delay from motors. Dashpot damping provides silent, splash-free operation.
The unit accepts the H20-93 Photocell Sensor to detect head entry.
H14-05ME : Extended Liquid Dipper - Mouse
H14-05RE : Extended Liquid Dipper - Rat
H14-05-LR : Liquid Reservoir (Extra) (For H14-05, -05M & -06)
Spare reservoir for replacement or extra to use whilst others are being cleaned etc.
H14-06R : Combination Liquid Dipper / Pellet Trough – Rat
Module Height: 4 Units
Lamp Type: 85 (Two) (this module is totally stainless steel)
The combination dipper and pellet trough is designed for use when 2 levers are used with both pellet and liquid reinforcements. It permits the centering of both, with the levers on either side. Each access port is the same size as in the H14-01R and H14-05R. The ports are separated with the liquid to the left. The 2 magazine lights are operable independently.
When using an H14-01R Pellet Delivery Trough with an H14-22R-45 Pellet Feeder, the feeder must be centered on the module because the pellet chute is in the center of the pellet trough module. When you want to use the H14-06R Combination Dipper/Pellet Trough with the feeder, you must offset the feeder mechanism on the feeder panel so that the drop tube may be inserted in the pellet chute when you install the feeder module above it.
H14-06-CP-02 : Liquid Dipper Cup – .02cc
(For H14-05, -05M & -06)
H14-06-CP-04 : Liquid Dipper Cup – .04cc
(For H14-05, -05M & -06)
H14-06-CP-06 : Liquid Dipper Cup – .06cc
(For H14-05, -05M & -06)
H14-06-CPS-03 : Set Of Three Assorted Cups
(For H14-05, -05M & -06)
The dipper arm used in the H14-05M, -05R and H14-06R dippers is finished wi th a .01cc volume cup machined directly into the end of the arm. For larger volumes, interchangeable cups may be ordered and attached to the end of the arm. They slip over the end of the arm and are held in place by a small, recessed set screw. The cup and screw are stainless steel. An Allen wrench is provided with the cups.